Appendix B - Complete command list

Note

COMMAND TEMPORISATION All commands can be temporised (i.e.: associated to a starting time) adding a proper suffix. There are two possibilities:

absolute temporisation (the operation will be performed at the indicated time): @DOY-HH:MM:SS, where DOY is the Day-Of-Year (1-366) and HH:MM:SS is the UT time;
iterative temporisation (the operation is performed now, then periodically according to the indicated time interval): @!DAYS-HH:MM:SS, where DAYS is the number of days and HH:MM:SS is hours, minutes, seconds.

Commands (temporised or not) can be used also in the init/pre-scan/post-scan procedures inside schedules. Observers are in charge of considering if and when the use of a certain command makes sense in their schedule, according to their specific needs and goals: this is something that no schedule parser can check!

Here follow all the commands exploitable in ESCS:

Note

Spaces within the command line content are not allowed!

> antennaPark: sends the antenna to stow position

> antennaReset: resets the alarm conditions

> antennaSetup=[code]: (code can be PRIM or SEC) unstows the antenna, sets it to tracking mode and configures the pointing model according to the specified focus (primary or secondary). It does NOT perform the receiver and backend setup

> antennaStop: stops the antenna. Activities can start again only commanding a mode change as antennaTrack (which does not affect the overall setup) or a new setup

> antennaTrack: sets the antenna to PROGRAMTRACK mode. It does not change the pointing model or any receiver setup

> asOff: disables the AS tracking: actuators go to the fixed position set for 45° of Elevation

> asOn: enables the AS tracking: actuators move according to the pointed Elevation (with a 0.5° step)

> asPark: sends all the actuators to their lowest position

> azelOffsets=[double]d,[double]d

sets the Az-El offsets (degrees). They are intended “on sky”, i.e. it is the actual offset run on the sky at the source Elevation.

Example: > azelOffsets=-0.05d,0.05d

> calmux=[code]: (code can be TOTALPOWER, DBBC) configures the calibration diode multiplexer

> calOn: switches the calibration mark on

> calOff: switches the calibration mark off

> chooseBackend=[string]: selects the backend; string can be BACKENDS/TotalPower

> chooseRecorder=[string]: selects the backend; string can be MANAGEMENT/FitsZilla, MANAGEMENT/CalibrationTool or MANAGEMENT/Point

> crossScan=[scanFrame],[span],[duration]: performs a cross-scan on the previously selected target (indicated using the track or sidereal commands), along the scanFrame (EQ, HOR or GAL), spanning span degrees in duration seconds

> device=[sect]: computes the beamsize, taking into account the present receiver and backend configurations relative to section sect

> flush=[N]: deletes the N-th element in the queue of temporised commands

> flushAll: deletes all the queue of the temporised commands

> fTrack=[dev]

It collects all the required data from the antenna, the back-end and the front-end, plus the information provided by the user (see the radialVelocity and restFrequency commands), then it tunes the telescope devices in order to centre the line(s) in each section bandwidth. The command lets the user select which device [dev] is asked to perform the tuning:

LO: only the front-end local oscillator is moved
ALL: the back-end performs a sub-tuning in the various sections

> getAttenuations: reads the attenuation values (dB) currently configured for the active sections, and lists them according to increasing section number

> getTpi: reads the signal intensity (raw counts) for the active sections, and lists them according to increasing section number

> goOff=[frame],[beams]: slews the antenna to an offset position, wrt a previously commanded target, along the longitude axis of the indicated coordinate frame (EQ, HOR or GAL). The user provides the offset value expressed in beamsizes. If the frame is HOR and target lies beyond the Elevation cutoff limits, the offset is applied in Elevation.

> goTo=[double]d,[double]d

sends the antenna, while in TRACKING mode, to the specified Az-El position.

Example: goTo=180d,45d

Arguments are always rounded in the range 0-360 and 0-90 for azimuth and elevation respectively (in any case the ranges are limited to mechanical contraints). The jolly character is valid and is considered as: keep the present value. The differences from the preset command are:

once the antenna reaches the destination, the system will acknowledge the “on source” status;

the pointing corrections (pointing model and refraction) are applied. In case they are not required they must be turned off explicitly.

> haltSchedule: completes the current scan and then stops the schedule

> ifdist=[int]input,[int]pol,[double]att

set/get the configuration for IF Distributor

input can be:

1 to select output on A

2 to select output on B

pol can be:

-1 to get the current value of pol for selected input

0 no input selected

1 vertex Right Pol (A input) or ricevitore in vertex Left Pol (B input)

2 L Right Pol (A input) L Left Pol (B input)

3 X Right Pol (A input) ricevitore X Left Pol (B input)

4 S Right Pol (A input) ricevitore S Left Pol (B input)

5 spare (A input) S Right Pol (for geo obs.) (B input)

6 spare (A input) spare (B input)

att can be:

-1 to get the current value of att for selected input

a value in the range 0 - 63, each step is 0.5 dB

> initialize=[code]: (code can be CCC, MMC, KKC, QQC, …) configures the backend using the default parameters relative to the selected receiver. It does not act on the receiver, pointing model or antenna mount mode.

> integration=[double]: sets the backend integration time (ms)

> log=[filename]: defines a custom name for the logfile (do not specify the extension)

> lonlatOffsets=[double]d,[double]d

sets the Galactic b-l offsets (degrees). They are intended “on sky”, i.e. it is the actual offset run on the sky at the source latitude.

Example: > lonlatOffsets=2.0d,-1.0d

> moon: points the antenna to the present coordinates of the center of the Moon

> preset=[double]d,[double]d

sends the antenna, if in PRESET mode, to the specified Az-El position, without applying any pointing correction. This is useful when needing to point to a position next to the zenith. Beware: the antenna will reach the destination but no “on source” flag will be raised.

Example: > preset=180d,45d

> project=[code]: lets the system know which project is observing (the code/name must correspond to the one provided by the TAC). This code/name is then considered as default when launching schedules: the system will search for them in a folder named “project/schedules”. This code/name also forms part of the output FITS filename. Notice that the PROJECT keyword indicated inside the schedule, which is then written in the “Project Name” keyword in the FITS main header, is a free string and might differ from the project official name.

> radecOffsets=[double]d,[double]d

sets the RA-Dec offsets (degrees). They are intended “on sky”, i.e. it is the actual offset run on the sky at the source Declination.

Example: > radecOffsets=1.0d,0.0d

> radialVelocity=[vrad],[vref],[vdef]

[vrad] (radial velocity) is in km/sec if vdef is not Z
[vref] (reference frame) can be one of the following:
- BARY: Solar System BARYCENTRE
- LSRK: Kinematic Local Standard of Rest
- LSRD: Dynamical Local Standard of Rest
- LGRP: Local Group
- GALCEN: Galactic Centre
- TOPOCEN: TOPOCENTRIC (observer’s frame)
[vdef] (velocity definition) can either be:
- RD: Radio Definition
- OP: Optical Definition
- Z: stands for Redshift

The specified velocity parameters are valid until a new target is commanded. The radialVelocity command overrides any other velocity value that might have been differently expressed

> receiversMode=[code]: configures the working mode of the receiver, according to its peculiar characteristics

> receiversSetup=[code]: (code can be CCC, MMC, KKC, QQC, …) configures the receiver using the default parameters. It does not act on the backend, pointing model or antenna mount mode

> restFrequency=[freq1];...;[freqN]: [freq] is given in MHz and is a multiple argument: it can list a different value for each of the N sections - as long as XARCOS is the backend in use(not all the backends allow this sub-tuning). Specifying a single value assigns the rest frequency to all the sections. The specified values will hold until different ones are commanded, or until a new general setup command is entered.

> setAttenuation=[sect],[att]: sets to att (dB) the attenuator of section sect

> setLO=[freq]: Local Oscillator frequency, in MHz (one per IF, separated by “;”, usually the values are identical) This LO frequency corresponds to: SkyFreq(@band start) – 100 MHz when using the TPB

> setSection=[sect],[startFreq],[bw],[feed],[mode],[sampleRate],[bins]: configures the backend section sect.

> setupCCC (setupKKC, etc…)

unstows the antenna, sets it to tracking mode, selects the pointing model, and configures the receiver and the backend using default parameters. In practice, it is a shortcut corresponding to this sequence:

> antennaSetup=[code]
> receiversSetup=[receiverCode]
> initialize=[receiverCode]
> device=0
> calOff

> sidereal=[sourcename],[RA],[Dec],[epoch],[sector]

points to the supplied RA-Dec position and temporarily assigns the sourcename label to it. Epoch can be 1950, 2000 or -1, the last one meaning that the provided coordinates are precessed to the observing epoch. The sector keyword forces the cable wrap sector, if needed: its value can be CW, CCW or NEUTRAL. The last option means the system will automatically choose the optimal alternative.

Example: > sidereal=src12,319.256d,70.864d,2000,neutral

> skydip=[El1]d,[El2]d,[duration]: performs an OTF acquisition at the current azimuth position, spanning in elevation from El1 to El2 (both expressed in degrees, with ‘d’ suffix), in duration time, expressed in hh:mm:ss. A recorder must have previously been enabled in order to save the data, and a reference position must have been selected via a sidereal, track or goTo command.

> startSchedule=[project/][schedulename].scd,[N]: runs schedule schedulename.scd (project is the ID of the observing project, it is optional if it has already been input through the projectCode command), reading it from line N

> stopSchedule: immediately stops the running schedule, truncating the acquisition

> ti: lists all the active temporised commands

> track=[sourcename]: points the antenna, in sidereal tracking, to the specified source, which must be present in the local catalogue

> tsys: measures the system temperature (K) in the position the antenna is pointing to. It returns a list of values, one for each section in use. Intermediate steps and calculations are stored in the active logfile

> wait=[double]: sets a delay (in seconds) which is applied before the system reads/executes the next command

> wx: returns the current weather parameters: ground temperature (°C), relative humidity (%), atmospheric pressure (hPa), wind speed (km/h).